Skip to content
Prompt CRM

Health checks

Digital vehicle health check software for dealer workshops

What a digital vehicle health check covers, how to rate red, amber and green, what the software must do and which numbers prove it works.

By
Thilo Krause
Published
Updated
Reading time
7 min read

Digital vehicle health check software replaces the paper check sheet a technician fills in at the ramp. The technician works through a fixed list of items on a tablet or phone, rates each one red, amber or green, enters the measured values and takes a photo or video of anything the customer should see. The service advisor prices the findings. The customer then approves, declines or postpones each item from a link on their phone.

Good software makes that chain fast and keeps a record of every decision. It also counts what the workshop found and what it sold, which is the number a service manager needs every week. Whether a digital check pays for itself depends on two things the workshop sets itself, whatever product it buys. One is the rating rules. The other is the speed of each hand-off.

What a digital vehicle health check is

A vehicle health check (VHC) is an inspection of the same set of items on every car that comes in, whatever the customer booked it for. The digital version, often called eVHC, records the results in software instead of on paper.

On paper, the technician writes what they saw, the advisor reads it later at the desk, and the customer hears a summary on the phone. Each step loses detail. The advisor cannot see the worn disc, and the customer has to trust a voice.

Digital changes three things. Every item becomes a structured record with a rating and a measured value, so you can report on it. The evidence travels with the finding, so the advisor and the customer see what the technician saw. And every step gets a time stamp, so you can see where a check waits and for how long.

What to check, and how to rate red, amber and green

Build one template per service type and keep it short enough that technicians finish it on every car. A typical passenger car template covers these items:

  • Tyres: tread depth per tyre in millimetres, damage, age
  • Brakes: pad and disc thickness front and rear, brake fluid condition
  • Battery: test result
  • Lights, wipers and washer
  • Windscreen: chips and cracks in the driver's view
  • Underside: exhaust, suspension joints, steering, drive shaft boots, leaks
  • Fluids and drive belts

The ratings need more care than the template, because a red that means something different on each ramp tells the customer nothing. Write down one rule per colour and train it.

Red. Safety-relevant or below a legal limit now. The customer should hear about it before the car leaves.

Amber. Working today, but worn or measured close to the limit, so it will need work soon. Most amber items are candidates for the next visit.

Green. Checked and in order. A green item still gets ticked, so the customer can see it was checked.

Then set a threshold for every measured item. Tyres are the clearest case. In Germany, § 36 (3) StVZO requires a main tread depth of at least 1.6 mm around the whole circumference, so anything below that is red. Where amber starts is your decision. Pick a number, for example 3 mm, and put it in the template so every technician rates the same tyre the same way. Do the same for pads, discs and battery test values.

Use the three colours only for health check urgency. If the same red also marks a late part or an overdue order on your screens, the colour stops meaning safety to the people who read it.

Photos and video the customer can judge

A finding without a picture asks the customer to take your word for it. A photo per red and amber item fixes that, as long as the photo shows the measurement. Put the tread gauge in the groove. Hold the worn pad next to a new one. Show the crack with the wiper beside it for scale.

Video does a different job. A short clip in which the technician walks round the car, names each finding and points at it gives the customer a reason to believe the list that follows. Keep it short and plain. The customer should be able to watch it in a car park on a phone.

Two habits keep media useful. Attach each photo to the finding it explains, so it shows up next to the right price. And film only the customer's car, with no other number plates in the frame.

From the technician to the advisor to the customer

A digital check pays off only when each hand-off happens quickly. The usual sequence looks like this:

  1. The technician submits the check with all findings, photos and the video.
  2. The advisor prices each red and amber finding with parts, labour and a price including VAT, and writes one plain sentence per item.
  3. The customer gets a link, watches the video and decides on each item.
  4. Approved items become job lines, and the parts desk picks or orders the parts.
  5. Declined and postponed items stay on the vehicle record with a date to follow up.

Set a target time for each step and give each one an owner. If nobody owns the time between "check submitted" and "estimate sent", the car sits on the ramp while the advisor deals with the front desk. In Prompt CRM the defaults are a pricing task for the advisor due 15 minutes after a check with findings is submitted, a reminder to the customer after 20 minutes without a decision, and a call task for the advisor after 45 minutes. The automation rules show how each one is stored.

The approval step has a legal side. Consumer law on extra work differs by country, but the direction is the same. The UK Motor Industry Code of Practice for Service and Repair (clause 3.2) says an accredited business will contact the customer for authorisation before it starts additional work that was not previously recognised. In Germany, § 649 (2) BGB obliges a contractor to tell the customer without delay when a cost estimate is expected to be substantially exceeded. A per-item approval with a stored record gives you the evidence in both cases. A phone call nobody wrote down gives you none.

What to look for in VHC software

Use this list when you compare products or test a demo. Each point comes from one of the steps above.

  • Templates per service type, with measured values per item as well as a colour
  • Thresholds stored in the template, so the rating follows the measurement
  • A photo per finding and a video, both attached to the check
  • An app the technician can use with gloves on, with large buttons and few screens
  • A pricing screen that turns findings into priced lines with a plain sentence each
  • A customer page that opens from a link, without an account or an app
  • A decision per item (approve, decline, postpone) with the new total shown
  • A record of who decided, when, on which items, at which price and through which channel
  • A task with a due time whenever a check waits on the advisor or the customer
  • Postponed items kept on the vehicle with a follow-up date
  • Reports on health check rate, video rate and found versus sold work

Ask to see the last three on real data in the demo, because a slide cannot show whether they work. The eVHC software page describes how the health check runs in Prompt CRM, from the technician's tablet to the customer's decision.

How to measure a digital vehicle health check

Four numbers tell you whether the check works. Measure them over the same period, for example the last 30 days.

MeasureFormula
VHC rateOrders with a submitted check ÷ all orders
Video rateChecks with a video ÷ submitted checks
Red sold rateRed items approved ÷ red items found
Amber sold rateAmber items approved ÷ amber items found

Count the sold rates twice, once by number of items and once by value. A workshop that sells many wiper blades and few brake jobs looks good by count and poor by value.

Take an example workshop with 400 orders in 30 days. Technicians submit a check on 340 of them, so the VHC rate is 85 %. They record 120 red items worth €24,000 and 300 amber items worth €45,000. Customers approve 78 red items worth €15,600 and 60 amber items worth €8,100. The red sold rate is 65 % by count and 65 % by value. Amber is 20 % by count and 18 % by value.

Each number points at a different fix. A low VHC rate is a workshop process problem, because cars leave without a check. A low red sold rate points first at the evidence and the advisor's explanation, so look at the photos and the sentences on the unsold items. A low amber rate on the day is less worrying. By your own rule, amber is work that is due soon, so many customers will postpone it. That makes the follow-up of postponed items the second half of the job.

Prompt CRM shows the VHC rate, the video rate and red and amber findings found versus sold, by count and value, in the service manager's 30-day performance report.

Start with the ratings. Write the threshold for each measured item into the template this week and check a sample of ten submitted checks against it. Once every technician rates the same tyre the same way, a red on the customer's phone means the same thing on every car, and the sold rates become numbers you can act on.

Sources

All articles

Analytics

May we measure visits to this site with Google Analytics? It loads only if you accept.

Details in the privacy policy